Home / Electricity & Magnetism / Wheatstone Bridge

Wheatstone Bridge

JEEWBJEE
Galvanometer current: 0 mA P/Q: 0 R/S: 0 —

The physics

Four resistors form a bridge with a galvanometer connected across the midpoints. This simulation solves the actual circuit using Kirchhoff's current law at both midpoint nodes — it isn't a simplified approximation, so you'll see genuine galvanometer current for any combination of resistances, not just near balance.

Balance condition (zero galvanometer current): P/Q = R/S  i.e.  PS = QR
At balance: unknown S = QR/P

This is exactly how a real Wheatstone bridge is used in the lab: P, Q, R are known resistances (R often a calibrated resistance box), S is unknown, and you adjust R until the galvanometer shows no deflection.

Exam tip: a very common NEET/JEE question swaps the battery and galvanometer positions — the balance condition PS = QR stays exactly the same, since it depends only on the resistor ratio, not on which arm carries the source.

Sample data: unknown resistance found at balance

At balance P/Q = R/S, so S = QR/P. The galvanometer shows zero current.

PQR (adjusted)Unknown SRatio Q/P
100 Ω100 Ω47 Ω47 Ω1
10 Ω100 Ω25 Ω250 Ω10
100 Ω10 Ω472 Ω47.2 Ω0.1
1000 Ω100 Ω123 Ω12.3 Ω0.1
100 Ω1000 Ω5.6 Ω56 Ω10

Conditions: ideal bridge with no galvanometer current at balance.

Notice: with equal arms (P = Q) the unknown simply equals R, but a ratio arm of 10 lets a 25 Ω rheostat reading find a resistance of 250 Ω, ten times larger. Because the measurement depends on a zero reading, the battery voltage does not enter the result.

🎯 Practice Zone

Puzzle 1. 🎯 Why is a Wheatstone bridge considered more accurate for measuring resistance than simply using an ammeter and voltmeter with Ohm's law?

A Wheatstone bridge is a "null" method — at balance, exactly zero current flows through the galvanometer, meaning the measurement doesn't depend on the galvanometer's own accuracy or calibration, only on the accuracy of the known resistors. An ammeter/voltmeter approach, by contrast, depends directly on how accurately those instruments are calibrated, and both instruments slightly disturb the circuit they're measuring (a voltmeter isn't infinite resistance, an ammeter isn't zero resistance) — introducing systematic error the bridge method avoids entirely.

Puzzle 2. 🔋 Why is the balance condition PS=QR completely independent of the battery's EMF or its internal resistance?

At balance, zero current flows through the galvanometer branch, which means the two halves of the bridge (P-Q and R-S) each behave as simple, independent series circuits carrying whatever current the battery drives through them. The ratio of voltage drops across P and Q (or R and S) depends only on the resistor values in each divider, not on the total current — so the battery's exact voltage cancels out of the balance condition entirely.

Puzzle 3. 🌡️ A metal's resistance changes measurably with temperature. How does this fact let a Wheatstone bridge be used as a precision thermometer?

Replace the unknown resistor S with a resistance temperature detector (RTD) — a resistor whose resistance changes predictably with temperature. As temperature changes, S changes, unbalancing the bridge; the galvanometer deflection (or the resistance box adjustment needed to re-balance) can be precisely calibrated against known temperatures. This null-method precision is exactly why bridge-based platinum resistance thermometers are among the most accurate temperature sensors available.

Puzzle 4. ⚖️ If you double all four resistances in a balanced Wheatstone bridge (P, Q, R, S all ×2), does the bridge remain balanced?

Yes, it remains exactly balanced. The balance condition is PS=QR — a ratio condition, not an absolute-value condition. Doubling all four values gives (2P)(2S)=4PS on the left and (2Q)(2R)=4QR on the right; since PS=QR originally, both sides remain equal after scaling by the same factor. Only the ratios between arms matter, never the absolute resistance values.

Puzzle 5. 📏 A meter bridge (slide-wire version of the Wheatstone bridge) gives more accurate results when the balance point falls near the middle of the wire (around 50cm) rather than near either end. Why?

Near the middle, a small error in reading the balance point position translates into a proportionally small error in the calculated resistance ratio. Near the ends (say, 5cm or 95cm), the same small positional reading error corresponds to a much larger percentage error in the length ratio used in the calculation — the sensitivity of the measurement to positioning error is worst at the extremes and best near the middle, which is why experimenters are taught to adjust the known resistance to bring the balance point close to 50cm.

Problem 1 (NEET level). 📘 In a balanced Wheatstone bridge, P=10Ω, Q=20Ω, R=15Ω. Find the unknown resistance S.

Balance condition: P/Q = R/S → S = QR/P
S = (20×15)/10 = 30 Ω

Problem 2 (JEE Main level). 📗 In a meter bridge, a known resistance of 10 Ω gives a balance point at 40 cm from the left end (100 cm wire). Find the unknown resistance.

Known/Unknown = balance length/(100−balance length)
Unknown = 10 × 40/(100−40) = 10 × 40/60
Unknown = 6.67 Ω

Problem 3 (WBJEE level). 📙 Using Problem 2's unknown resistor (6.67 Ω), if it's a 20 cm wire of cross-sectional area 0.5 mm², find its resistivity.

ρ = RA/L = 6.67 × 0.5×10⁻⁶ / 0.2
ρ = 1.67×10⁻⁵ Ω·m

Problem 4 (CBSE Class 12 level). 📕 A bridge has equal ratio arms P=Q=100 Ω and R=100 Ω (so balance needs S=100 Ω). If S is actually 101 Ω (1% off), estimate whether the galvanometer would show a detectable deflection for a sensitive galvanometer of resistance 50 Ω, with a 5 V battery.

Full nodal-circuit analysis for this near-balance condition gives:
I_galvanometer ≈ −82.8 μA
This is a small but easily measurable current for a sensitive galvanometer — confirming that even a 1% resistance mismatch produces a clearly detectable deflection, which is exactly the sensitivity that makes bridge circuits useful for precision measurement.

Problem 5 (JEE Advanced style). 📓 Verify, using full circuit (nodal) analysis rather than just the ratio formula, that a bridge with P=10Ω, Q=20Ω, R=15Ω, S=30Ω truly gives zero galvanometer current — for any galvanometer resistance and any battery voltage.

Solving the two-node Kirchhoff equations for this bridge (galvanometer resistance 50 Ω, battery 10 V) gives:
I_galvanometer = 0 A (exactly, to numerical precision)
This confirms the balance condition PS=QR isn't an approximation — it's an exact algebraic consequence of Kirchhoff's laws, true regardless of the specific galvanometer resistance or battery voltage used.
🔧
1833

Samuel Hunter Christie first describes the bridge circuit design in a paper to the Royal Society — the actual original inventor, though his contribution was largely overlooked for decades.

⚖️
1843

Sir Charles Wheatstone popularizes and extensively promotes the circuit's use for precise resistance measurement — and despite not being the original inventor, the design becomes permanently known by his name due to his effective advocacy and publication.

📏
Mid-1800s

The meter bridge (slide-wire variant) becomes a standard undergraduate physics laboratory instrument, prized for combining the null-measurement precision of the bridge principle with simple, inexpensive construction.

🌡️
Early 1900s

Bridge circuits are adapted for precision resistance thermometry (platinum resistance thermometers) and strain gauge measurement — extending Wheatstone's simple resistance-comparison idea into some of the most accurate measurement instruments in industrial and scientific use.

💻
Present day

The Wheatstone bridge principle remains foundational in modern electronics — used in load cells, pressure sensors, and countless precision measurement circuits, nearly 200 years after Christie's original description.